Today I attempted to write a short D&D campaign using the Homebrewery. It was a total failure. I was incredibly tired, and didn't manage my time well.

Today I attempted to write a short D&D campaign using the Homebrewery. It was a total failure. I was incredibly tired, and didn't manage my time well.
Ingredients needed:
Optional extras:
First, I aged the individual sheets.
In theory I think you can iron the sheets flat. If I did this project again, I would try it. It's hard to line up and glue wavy sheets.
I tried painting on the back, using a paint I made myself. I wanted something subtle, like the faint patterning on decorative paper. I tried tempura paint, using coffee in place of water, and flour-based tea paints. I got something that looked how I wanted.
I liked the effect, but I had a hard time reproducing the paint the next day. If you want to experiment, my recipe used something like 1 bag of tea, one cup of water, and about 2 Tbsp flour.
Next, I glued together the sheets to make a continuous scroll. For reasons you'll see later, I needed an extra strong glue. So as my first step, I made wheatpaste glue, which is very strong.
I glued together the sheets with wheatpaste. For some projects, it's easier and better to apply warm. But my paper was already fragile from the aging process, so I found it worked better all the way cooled.
I took a fingertip of glue, spread it evenly on the bottom of the page. Repeating, I covered the whole bottom. Then, I placed the next sheet over it, and laid them down so they matched. Since the aging process warps the paper, you may not get a perfect fit.
Then, use the pad your your thumb to press the sheets together firmly. Make sure to use rolling motions, don't drag your finger along. That can tear the paper.
My research suggested Zip Dry paper glue might also work.
As a fun fact, real scrolls were made by gluing together sheets, and they actually used wheatpaste glue! Scrolls were often glued left-to-right (volumen) instead of top-to-bottom (rotulus), but I thought the fantasy stereotype was more fun.
After the glue hardened, I cleaned off both sides and trimmed the edges to match exactly. Then I applied a gold tape on the edges. I had decorative borders printed already, so it was relatively easy to get tape pieces to match. I found the key was to go slow, and use many pieces of tape. After laying one down, I pressed it smooth with the back of a fingernail, flipped it, and did the same of the back. The washi tape I'm using is relative easy to remove again, but also shows defects pretty clearly.
I turned dowel rods to hold the scroll on my lathe. The middle segment is the width of a piece of paper. Then I added as much decoration as I could on each end, but my lathe is very small, so not much fit.
Then I stained and finished the dowel rods.
If like most people you don't have a lathe, you could glue something decorative on the ends of dowel rod pieces, cut bamboo segments, or decorate a paper towel roll.
It's also totally fine to just roll up the scroll and tie it closed with string or ribbon. No holders are really needed.
I made another batch of wheatpaste (much better this time).
I glued the scroll onto the dowel on the two ends.
The glue was very strong, but the ends only look okay. I trimmed the last couple inches of washi tape so the glue would stick.
If I did the project again, I'd try to keep the sheets flattened (wrinkly sheets after aging causes all kinds of problems). I'd also leave a little blank space on the top and bottom for attaching them to the rods.
I picked up some stranded steel rope, which I turned into a line with two loops at the end.
I looped them over the holes in the dowel. Voila! Now you can hang the scroll on the wall.
It's possible to make the wire hangers secure, but removable. For the first couple I made they're just secure--those suckers aren't coming off.
I dripped wax on the scroll and pressed down a seal I got on Amazon. It matches the theme of my D&D game very well, I was happy with how it looks.
The final scroll looks amazing.
One one hanger, it takes up the wall.
Between 6 pages and a dowel rod, that's why the glue between pages needed to be so strong!
By using two sets of hanging wires, you can show part of the scroll without taking up the whole wall. Here I'm showing the top of the scroll.
You can roll one dowel as you unroll the other, to show any part of the scroll. That's why long scrolls have two rods. It's also where the term "scrolling" up and down on a computer comes from.
I let each player pick the color of the wax for the seal and decorative ribbons. They didn't know exactly what they were giving me colors for.
I'm sure my players will love them!
By the way, if you're curious about the contents, this is a prophecy the players found in parts around the world. Underneath each of the 50 lines, are their player notes about where they found each piece. It's a souvenir for a campaign which ran for about 2 years, and is finally wrapping up.